Contours show the shape of the land on the Landchecker map, so you can see how a property or area slopes, where it falls and how steep it gets before you visit the site or order a survey. This article explains where contours sit in the Map Layers panel, how to turn them on, how to read them and how to use them with other layers.
Plan access: Contours are available on all Landchecker plans, including Free. Opacity, Favourites, exporting the map view, 3D terrain view and the Site Finder Topography filter have their own plan requirements, noted in their sections below. To see what's included on each plan, compare Landchecker plans.
What are contours?
Contours are lines on the map that join points of the same height. Together, they show the topography of a property or area: where the land rises, where it falls and how steep it is.
In Landchecker, contours sit inside the Topography layer, under the Heritage & Environment category in the Map Layers panel.
How do I turn on contours for a property or area?
Follow these steps to turn on contours on the Landchecker map:
Search for a property using the search bar at the top of the map, or zoom and pan to the area you want to check.
Click the Map Layers icon in the toolbar on the left-hand side of the map. The icon is a stack of layers.
Click Heritage & Environment to expand the category.
Tick the checkbox beside Topography. This turns on the 1–5m contours.
To see the 10–20m contours instead, click the arrow beside Topography and select 10–20m. Only one contour interval can be on at a time.
Contour lines appear on the map over the property and the surrounding area. They stay on as you move around the map and after you close the Map Layers panel. To turn contours off, untick the same checkbox.
Good to know: contours don't show when the map is zoomed too far out. If you can't see contour lines after you tick Topography, zoom in closer to the property or area.
Tip: type "contours" into the Search layers... box at the top of the Map Layers panel to go straight to the contour layers without opening Heritage & Environment.
To learn more about the Map Layers panel, read A guide to the left-hand menu on the Landchecker map.
Which contour interval should I use?
The contour interval is the difference in height between one contour line and the next. Landchecker has two contour intervals under Topography. Switch to 10–20m underneath it. Only one contour interval can be on at a time, so pick the one that suits what you're checking.
1–5m – smaller height steps between lines, so you see more detail. Use it for a close read on the fall across a single property, such as when you're thinking about cut and fill or drainage.
10–20m – larger height steps and fewer lines, showing the broad shape of the land. Use it for a large rural property, a whole suburb or anywhere the 1–5m lines are too dense to read.
The contour detail shown for an area depends on the elevation data available from our data source.
Which states and territories have contours?
Contours are available in every Australian state and territory except the Northern Territory. Contour data for the Northern Territory is coming soon.
State or territory | Contours |
Victoria | ✓ |
New South Wales | ✓ |
Queensland | ✓ |
South Australia | ✓ |
Western Australia | ✓ |
Tasmania | ✓ |
Australian Capital Territory | ✓ |
Northern Territory | Coming soon |
How do I adjust the opacity of contours?
You can make contour lines more or less see-through, so the aerial imagery or other layers underneath are easier to read. Opacity adjustment is available on the Advanced and Enterprise plans.
In the Map Layers panel, click Heritage & Environment and tick Topography. An opacity slider appears below Topography.
Drag the slider to the left to make the contour lines more transparent, or to the right to make them more solid.
The percentage to the right of the slider shows the current opacity of the Topography layer.
To learn more, read How to adjust the opacity of a planning layer.
How do I add contours to my Favourites?
You can save one or both contour intervals to Favourites in the Map Layers panel, so you can turn contours on without opening Heritage & Environment each time. Favourites are available on the Advanced and Enterprise plans.
Even if you save both contour intervals to Favourites, only one can be on the map at a time.
In the Map Layers panel, click Heritage & Environment, then click the arrow beside Topography.
Hover over 1–5m or 10–20m. A star icon appears beside it.
Click the star to add that contour interval to your Favourites.
To turn contours on or off from Favourites, click the contour interval in the Favourites section. To remove a contour interval from Favourites, hover over it in the Topography list and click the star again.
To learn more, read How to search planning layers and save favourites.
How do I view contours with aerial imagery, flood or planning layers?
You can have contours on at the same time as layers from any other Map Layers category. Turning on another layer doesn't turn contours off.
Some useful combinations:
Contours and flood: in the Map Layers panel, open Hazards and tick Flood to see how flood extents follow the terrain around a property.
Contours and planning controls: open Planning and tick Planning Zones or Planning Overlays to see how the land falls within the controls that apply to a site.
Contours and aerial imagery: open the map controls in the bottom-left corner of the map and select High Resolution Aerial Imagery to see contours over existing buildings, trees and driveways. All map types are available on the Standard, Advanced and Enterprise plans. If you're on the Free plan, upgrade to Standard to see contours over aerial imagery.
To learn more about checking flood risk with Landchecker, read How to easily and quickly check flood zones by address and NSW flood zones.
To learn how to switch map types, read How to change the map type and save a default.
Can I download a map image with contours on it?
Yes. You can download an image of the map with contours turned on, to use in a client report, a site plan or your project files. Export Current Map View is available on the Standard, Advanced and Enterprise plans.
Turn on contours and any other layers you want in the image.
Zoom and pan the map to frame the property or area.
Click Export Current Map View in the toolbar on the right-hand side of the map.
A PNG image of your current map view, including the contour lines, downloads to your device. If you're on the Free plan, upgrade to a paid plan to download map images with contours for your reports and site plans.
To learn more, read How to export high-res images and current map view.
Can I view the topography of a property in 3D?
Yes. 3D terrain view shows the elevation and shape of the land in three dimensions, so you can see how a property and its planning zones and overlays sit against the surrounding terrain. 3D terrain view is available on the Standard, Advanced and Enterprise plans.
Search for a property or zoom to the area you want to check.
Click the 2D button in the toolbar on the right-hand side of the map. The map switches to 3D terrain view.
If you're on the Free plan, upgrade to a paid plan to view the terrain around a property in 3D. To learn more, read How to display 3D terrain view.
Can I search for properties by slope?
Yes. The Topography filter in Site Finder lets you search for properties by slope across a whole area, rather than checking contours one property at a time. Site Finder is available on the Advanced and Enterprise plans.
You can select one or more of these slope types:
Slope type | Degrees | Percentage |
Flat | 0–2° | 0–3.5% |
Gentle | 2–5° | 3.5–9% |
Moderate | 5–10° | 9–18% |
Steep | 10–20° | 18–36% |
Very Steep | 20°+ | 36%+ |
If you're on the Free or Standard plan, upgrade to Advanced to filter sites by slope in Site Finder. To learn more, read How to use Site Finder.
Are contours included in property reports?
Yes. The Premium Property Report includes contours for the property, along with zones, overlays, hazards and easements. When you consolidate several properties and save the site to a project, the Consolidated Site Report also includes contours.
To learn more, read How to download a consolidated site report.
How can contours help with my work?
Contours give you an early read on the land itself. When you turn them on with the other data and tools in Landchecker, you can work out what a site's slope means for cost, design, drainage and planning in one place. Here's how different professionals use contours, and what to use alongside them.
Property developers
When you're assessing a sloping site for townhouses or a subdivision, you need to know how much the land falls, which way water will drain and how much to allow for cut and fill, retaining walls and stormwater works.
Use contours with:
Site Finder – set the Topography filter to Flat or Gentle, along with Size & Dimensions and Planning filters, to shortlist sites that suit your project before you check the contours on each one.
Easements under Planning – check for easements on the low side of the property, where stormwater and sewer lines usually need to run.
Flood under Hazards – see whether the low part of the site sits within a flood extent.
Distance tool – measure across the block between contour lines to see how quickly the land falls.
Site Consolidation and Projects – combine neighbouring lots to see the slope across a larger site, then save it to a project. The Consolidated Site Report includes contours.
Architects and building designers
When you're designing for a sloping block, you need to work out where the flattest building platform is, how a driveway will reach the street and how to show your client the way the home will sit on the land.
Use contours with:
High Resolution Aerial Imagery – lower the Topography opacity to see contours over existing trees, buildings and driveways.
3D Terrain View – show your client the shape of the land around the site.
Property Boundary dimensions, bearings and angles – read the boundary lengths against the slope when you sketch a building envelope.
Drawing Tools – draw a building footprint or driveway over the contours to test where it sits.
Export Current Map View – download a PNG image of the site with contours for your site analysis.
Town planners
When you're assessing a proposal on sloping land, you need to know whether the steep part of the site carries extra controls or hazards, and what council has approved on similar sites.
Use contours with:
Planning Overlays – check which overlays apply where the land is steepest.
Landslide and Bushfire under Hazards – see whether hazard areas line up with the steep parts of the site.
Cultural Heritage Sensitivity – it sits in Heritage & Environment alongside Topography, so you can check both in the same category.
Planning Permits – look at permits on nearby sloping sites to see what council has approved.
Valuers
When part of a property is steep, you need to judge how much of the land is usable and whether nearby sales are fair comparisons.
Use contours with:
Comparable Sales – check recent sales near the subject property, then turn on contours to see whether those properties are flat or sloping too.
Street view – see how the slope looks from the street, such as steps, retaining walls or a steep driveway.
High Resolution Aerial Imagery – compare capture dates to spot recent earthworks or new retaining walls that contours may not show.
Premium Property Report – keep a record of contours, zones, overlays, hazards and easements for your file.
Real estate agents
When you're listing or appraising a home on sloping land, buyers will ask about the slope, drainage and flooding, and how the property sits compared with its neighbours.
Use contours with:
Flood under Hazards – show buyers whether the home sits above the flood extent in the area.
High Resolution Aerial Imagery and Street view – show the land from above and from the street.
Premium Property Report – share a report with contours, zones, overlays and hazards, branded with your company logo.
Export Current Map View – add a map image with contours to your appraisal or buyer pack.
Conveyancers and lawyers
When you're reviewing a property for a buyer, contours give you an early warning about drainage and flooding before you read the title documents.
Use contours with:
Easements under Planning – see easements on the low side of the property, where drainage often runs.
Flood under Hazards – check flood extents around the property.
Document Searches – order the title and plan to confirm what each easement is for.
Investors
When you're comparing sites, you want to rule out land where the gradient would make development difficult and costly before you spend time on due diligence.
Use contours with:
Site Finder – use the Topography filter to shortlist sites by slope across a whole suburb.
10–20m contours on the Satellite map type – see the broad shape of a large rural or urban fringe parcel.
Planning Zones – check what the zone allows alongside the slope.
Projects – save the sites on your shortlist so you can compare them later.
Some of these features depend on your plan. Site Finder, opacity and Favourites are available on the Advanced and Enterprise plans, and 3D terrain view, all map types and Export Current Map View are available on the Standard, Advanced and Enterprise plans. Compare Landchecker plans to see what's included on yours.
What should I know before relying on contour data?
Keep these limitations in mind when you use contours in Landchecker:
Contours are indicative. Use them for early site assessment, not in place of a survey. For design, engineering or building work, order a feature and level survey from a registered surveyor.
Detail varies by area. The contour detail available depends on the elevation data available from our data source, so it isn't the same everywhere.
Recent changes may not show. Contours reflect the ground when the elevation data was captured, so recent earthworks, retaining walls or new buildings may not be shown.
Frequently asked questions
Where are contours in Landchecker?
Contours sit inside the Topography layer, under Heritage & Environment in the Map Layers panel. Click the Map Layers icon in the left-hand toolbar, click Heritage & Environment, then tick Topography to turn on the 1–5m contours. TTo see the 10–20m contours instead, click the arrow beside Topography and select 10–20m. Only one contour interval can be on at a time.
Can I turn on both contour intervals at the same time?
No. Only one contour interval can be on at a time. Use 1–5m for a close read on the fall across a single property, and switch to 10–20m to see the broad shape of the land across a larger area.
I used to turn on contours from Planning Layers. Where are they now?
Planning Layers is now called Map Layers, and Topography moved from the Planning category to Heritage & Environment. Contours are still inside Topography. You can also type "contours" into the Search layers... box at the top of the Map Layers panel to go straight to them.
Which states and territories have contours in Landchecker?
Contours are available in Victoria, New South Wales, Queensland, South Australia, Western Australia, Tasmania and the Australian Capital Territory. Contour data for the Northern Territory is coming soon.
Which Landchecker plans include contours?
Contours are available on all Landchecker plans, including Free. Opacity and Favourites are available on the Advanced and Enterprise plans. Export Current Map View and 3D terrain view are available on the Standard, Advanced and Enterprise plans. The Site Finder Topography filter is available on the Advanced and Enterprise plans.
Why can't I see contour lines on the map?
First, check that Topography is ticked under Heritage & Environment in the Map Layers panel. Then zoom in closer, because contours don't show when the map is zoomed too far out. If the property is in the Northern Territory, contours aren't available there yet, and Northern Territory contour data is coming soon.
What's the difference between contours and the Site Finder Topography filter? Contours show the shape of the land on the map for any property or area you look at. The Site Finder Topography filter searches for properties by slope type, such as Flat or Steep, across a whole area. Contours are available on all plans, and Site Finder is available on the Advanced and Enterprise plans.
Can I make contour lines easier to see over aerial imagery?
Yes. On the Advanced and Enterprise plans, tick Topography in the Map Layers panel and drag the opacity slider below it. Drag left to make the contour lines more transparent, or right to make them more solid.
Can I use Landchecker contours for design or building work?
Landchecker contours are indicative and suited to early site assessment. For design, engineering or building work, order a feature and level survey from a registered surveyor.
Can I see contours and flood layers at the same time?
Yes. Turn on contours under Heritage & Environment, then open Hazards and tick Flood. Both layers stay on together, so you can see how flood extents follow the terrain.
Can I download a map image with contours on it?
Yes. Turn on contours, frame the property on the map, then click Export Current Map View in the toolbar on the right-hand side of the map. A PNG image of your current map view, including the contour lines, downloads to your device. Export Current Map View is available on the Standard, Advanced and Enterprise plans.
If you have questions or need help, use the live chat in Landchecker and our team will be happy to assist.

